It is wide compatible. The table headset hook supports all sizes of earphones. B&O H8/ H4/ Beoplay H9i, beyerdynamic headphones, B&W headsets, HyperX Cloud II's, Astro A50, Ra zer Gaming Headphones, Logi tech Headphones, Audio Technica headphones, R OG gaming headsets, etc. Small and foldable design saves space. It can be used to free your desktop from chaos. Safe and Stable: The headphone stand has strong glue that will allow it to last a long time. The materials are high-quality. The rubber pads on the headband protect it from wear. All kinds of headphones, such as wired headphones, wireless headphones, gaming headphones, TV headphones, and so on, are suitable for the universal headset holder. It's easy to install and can be mounted anywhere. On computers, desk, and wall. Clean the surface by using wipes.
👤I was very happy with my purchase of this headphone holder, but it has been a year since I purchased it. I noticed that my headphones got in my hair when I noticed the odd goop on the bridge. The pull out bracket that my headphones rested on was the culprit. I was able to use alcohol wipes to remove all of the liquified glue and I was also able to repair the small pad that locks the brackets in the closed position with some automotive grade 3M double sided tape. Hopefully it will hold up better than what was used to assemble it. Is this the end of the world? I am going to keep an eye on it because it was a quick repair.
👤I have a charging station in my laundry room. The hug makes it look less cluttered and it gets a lot of stuff off the counter. I charge a lot of stuff on this station. The double sticky tape is used. I made it even more solid by attaching a couple screws to the holes. Unable to keep earbuds and headphones off the countertop while charging. If you don't have anything to hang on it, this is a great option. I'm very happy with the space that was cleaned up.
👤The option to screw it into your desk is what I bought this hook for. I tried the glue before I tried to put it in. I had low expectations, but the sticker is so strong that it's like a combination of Ultimate Warrior and Hulk Hogan. I'm thinking about buying another one for my towels.
👤My father built a desk for me that is solid wood. It was built for writing, not a computer. I used the glue that came with the product because I couldn't drill a hole in it. I have a very light-weight Sony headphones, but they haven't budged over a month. The hook portion is large and padded to not damage my headphones. I might put two different pairs on there. I love that when I move this desk, I can just close the hook and it won't be a problem. There is a The metal is heavy and shiny. It's a good addition to my desk. I wish it didn't have the logo, but it is perfect.
👤Unfortunately it did not last. It fell off my wall in the middle of the night, luckily it didn't break my headphones, I was sleeping. It was loud. I might use it on a wood surface with screws to hold it up instead of giving it to someone else. Holds fast to painted plaster. I've considered buying another one just for the tape. It has been on the painted plaster walls for a long time. It holds my headphones and doesn't bang when I place them down. The inside of the "hook" is made of some kind of material. It doesn't open without you meaning it to.
👤This is what it seems to be. I thought it would be bigger but it is not. I used the two screws instead of using the glue to stick to the wall. I would have been concerned that the headset wouldn't hold it's weight. There is a This looks great on the wall. When I moved my console, I realized I lost the space I wanted for the headset stand and that's when a hanging stand became optimal. This is in front of my console. It's difficult to pull it down when it's folded up, because you don't have headsets on. I think that will loosen over time with use and shouldn't be a negative.
IPX5 waterproof Certificated with IPX5 waterproof,headphones are strong enough to resist all the penetration from splash and water. There is no worry about all-kinds of outdoor activity. There is a stand for multi-phone calls. Their stylish headphone stand is made of solid metal and has a design that makes it easy to clear space on your desk. Their headphone stand is easy to set up and assembly with no tools required. Attach the top of the stand to the base and you are ready to hang your headphones. You can keep your cables, pens, notes, cell phone and headphones in their spacious tray. Their headphone stand is perfect for your home or office. Their stand can hold any brand of headphones. The headphone hanger is a safe and secure way to keep your headphones in pristine condition. Be sent by AVANTREE. In the digital age, headphones are convenient for all of your calls, games, and music. Who wants them to be laying around and disorganized? If you are looking for a stable storage solution for your headphones, their headphone stands are the one for you. The mix of cutting-edge technology and elegant design is what they offer. Their stands come with a full warranty.
👤I needed a rest and saw this one. I bought it. The flimsy plastic that holds the top headphones is hard to put on. I think it should be all metal, so don't try to stack a bunch of headphones on it. Would I buy this product? Absolutely not! Spend your hard earned money on something better.
👤I think the top plastic piece should be stronger. I haven't been able to find any stands that hold 2 pairs of headphones. I bought two more stands. The price is right and there's a chance they'll surprise me and work perfectly well for many years. There is a * I was disappointed that the top piece of the headphones was very flimsy, as soon as I unboxed it and put it together. I have no problem with plastic, but it seems inevitable that the stand will break and make it useless, since it is so thin and flexible. If it falls off a table or shelf, someone accidentally pushes on the plastic hangar tab, or if you carelessly drop your headphones onto the tab, breakage is likely. The upright and post are made of metal and I don't have to worry about them breaking. If the top piece were metal, this would be a 5-star product.
👤I was expecting the entire structure to be made of metal but the hangers that hold the headphones are made of plastic. The wireless headset is held up by the hanger but it bends slightly when it is held up. There is a The stand is easy to assemble, but I expect it to become wobbly over time due to the toolless and screwless design.
👤It is very easy to assemble without tools. I think this would get worse with time. The plastic bend under the weight of my headphones is the top horizontal bar. I bought a less expensive stand after returning it.
👤Not bad for the money. The headphones are plastic and not metal. I think the plastic is more gentle on your headphones. I think an all metal stand is a better design because it has padding for the metal top piece. It would cost more to make that design. People would not mind paying more for quality. I have ordered 3 stands. Great product. I took a star away for not being all metal.
👤I needed to keep the headphones off the community study desk when not in use. A type A mom has had a ton of chaos caused by distance learning and an increase in sales related to organization. I was tired of cords everywhere and random headphones laying around and because they are teenagers who love video games, they need bulky headphones with mics. I thought they would decline the offer for AirPods. If it isn't holding two pairs, you do risk tipping, because it's balanced so you don't risk falling over with one set on.
👤I need a double stand because I have two wireless headsets that I alternate use. It doesn't feel sturdy like other reviewers have said, and you can see the bar is flexing when you put the headphones on. It doesn't feel like it's going to break and I'm happy with the price. An all metal option would cost more. I've been using it for a month. Will update with long term notes if necessary.
The curve shape makes the stand more stable. Designed to protect your headphones. The Arch bridge shape allows you to put the headphones, game controller, cell phones, and mp3 player on the middle of the headset stand, so your computer desktop won't look messy. The material is made of walnuts and is smooth, comfortable, and eco-friendly. Function: The stand is designed to keep your headphones out of the way of dust and scratches. The stand is sturdy and has rubber feet on the base to keep it from sliding. There is a 2 year satisfaction guarantee forValuable gift for Christmas, Thanksgiving day, Easter, Birthday, Valentine's day and more.
👤The piece is strong. The arch is cut with a band saw and is unattractive. If you remove the base, you can use fine sandpaper to make the edge softer, but the veneer is so thin you can't see the wood in the next layer. I did not attempt to glue the base to the arch, but returned. The saw blade marks are visible on the laminated edge. The surface is smooth. I could have refinished myself. I would have liked to have kept this, except for the crude joint between the arch and base.
👤There are no complaints about this stand. The stand is elegant and has nice layers of wood and veneer. Lower your expectations on fit and finish. Some quality problems are revealed by looking closer. There is a The upper arch to support the headphones and the lower arch that stands on the desk are both screwed together from the bottom of the lower arch. The screw holes are messy. They are out of sight so there is no big deal. It surprised me. The two arch pieces meet in this location. There is a noticeable gap on each side of the joint. It is roughly cut and finished. If I had to guess, a band saw would cut these without much sanding or attempts to make the joints appear curved. The intent is to have the stand appear as a single piece of wood but these gaps and rough cuts kill the design up close.
👤The stand is sturdy. The padding on my Bose headphones became stuck to the stand. I have to throw the stand away and replace the padding on the headphones.
👤It works perfectly with my Sony MDR-Z7 phones. It looks more expensive than it is. I don't like manufacturing defects and I won't see any on this. A reviewer said that if you turn it upside down, the pilot holes for the screws that hold it together are missing. Don't turn it upside down, it's impossible to make soft plywood with a sharp angle, and you can't get any chips, so get over it. Enjoy!
👤This is a great stand for my headphones. It is an absolute beauty and looks great in any setup that I have it in. I was worried about it tipping over, but I no longer worry about that, and it helps shape my headband. I mean by that because my previous stand had a bar at the top that was stretching out my headband, but now the stand is curved, which makes it easier to fit my headband in. There is a In the humid environment of Hawaii, my headphones are going to end up sticking to the stand because of the shiny coating on them. I hope the ear pads on my headphones are not expensive. Time will tell. I would like to see a different version that was more of a matt finish. It would look better, and it would also eliminate the worry of my ear pads sticking to the coating. They're worth the money. There are a few manufacturing issues with these items, but it's not unusual.
The convenience and company are two things. Their headset hanger is compatible with major brands including Bose, Bose, and Audio-Technica, and is 5 cm at the headband. Even the largest gaming sets can be held with ease. The mount has a surface area twice the size of the original for an incredible hold. There is a built-in cord management. The cords are secured under the desk by the stowStrap. The premium glass reinforced composite body is twice the strength of cast aluminum and has the perfect amount of friction. There is an optional screw mounting hardware. An extra 3M pad is also included.
👤Wow! How did I not notice this product sooner? There is a I own several headphones. I have spent a lot of money on stands to display the headphones. I find that some of the stands take up a lot of space on the desk counter as my workspace shrinks. I found this product through a deals website. I had no idea that there was aNCHOR PRO, but when I saw it, I thought to myself, "What a great idea." " I could have gotten the standard version for less. I decided to spend a few dollars more to get the Pro because I was interested in the cord-management feature. I'm very happy that I did. The anchor feels something. Like an anchor without the weight. It is a very good product. You can either use the 3M tape or the included screws to install the anchor pro. You can't go wrong with the tape. I was very pleased with the strength of the install. I pressed the anchor in place beneath my workspace after removing the protective cover. Before hanging your headset, it is important to let the anchor sit for 24 hours to "cure" There is a A tug at the attached anchor gives me a sense that this thing is not going away. The product is kept in place by the strong glue. The PRO version is the best for the cord management system. Two very high-quality cord managers are included. You can thread your charging or headphone cord through the clips if you unclip them. The clips have glue on them, which makes them easy to misplace. I use this for my headphones. The ANCHOR PRO keeps them in place. The cord system keeps my charging cord ready. This is an amazing product that is used and quality is excellent. Go ahead and purchase this product.
👤I did not purchase this product for headset organization. I was looking for something to hold my two lantern flashlights. I wanted a product that could be screwed under a cabinet. This product fit the bill. I put it under the cabinet in the laundry room. The flashlights are easy to see and can be charged right where they are. I did it because I didn't want to move the dryer. I wanted to be able to easily remove the hook in the future, so I didn't want to use 3M tape. The manufacturer included a drill bit for the screws. How often do you see that? Not very. There are two pads in the package for those who want to use the tape. One is on the hook and the other is the backup. If you want to, you can remove the tape from the hook, but it gets stretched out. I took it off, but realized I needed to put padding between the hook and the cabinet or my flashlight handles wouldn't clear the little wings at the end of the hook. The hook is useful for mounting my flashlight.
Customer service is great. Give it a try. You can return it within a month if you don't like it. They will send you a new one if it is faulty within a year. Universal under design allows for a near universal fit on most desks by attaching a thin, narrow, and thick piece of metal to them. It is easy to remove the Spring Clamp. The audible headphone arm swings underneath your desk for discreet and non-intrusive storage and swings back out for easy access. BUILT IN CABLE LOOP holds your headset's cable in place to prevent it from dragging on the ground or getting caught between your desk chair's legs. Soft rubber pads are located on both ends to protect your desk or table from damage. The under desk mount is convenient for storing. Easy installation of a springed C Clamp.
👤We needed a better solution to keep our headphones from breaking and this was our answer, it's very sturdy and feels very well made, it's even better if you have an xbox one controller, it's even more perfect. My purse is probably around 10 lbs. I'll probably order more for myself and gifts in the future. Highly recommended.
👤The hook portion can bend if you put a lot of weight on it and it is very cheap. There is a The head doesn't lock up. The clip is not tight enough to prevent desk steps that are less than a quarter of an inch from moving. You can get a Brainwavz Hengja Hanger for the same price that has better construction quality. I would've gotten a second one, but I got this instead when the page from my old order suddenly said out of stock and started directly to a screen protectors. I wouldn't buy it again. Cheap, poor construction, plastic bends, top sticks up a lot. A bad product.
👤It's easy to put my headphones out of the way. I didn't want one where you have to use glue or screws. You don't need a heavy duty one if you have light headphones. The mount has a sufficient amount of space. The desk is protected by the padded clamps. The mount has a hook so you don't lose your headphones. You can choose which direction you want to hang your headphones. The cord clip is nice, but it's stiff, so I just wrap it around the hook and grab my headphones when I need them.
👤This thing is great. I was embarrassed that I didn't think of getting this a long time ago, but I did not know it existed. Maybe it didn't. I am a recording artist and I use expensive headphones. They were not taken very well care of in the past, as they would flop around on various surfaces. The device is easy to set up and I like that the hook can be changed to hang things or not. I think it's a good deal so that I can get another one for my other cans. I recommend this to anyone who wants to protect their investment.
👤It was easy to put in place. I got this because I was sick of my headphones laying in random places. The hook is neatly underneath. The picture doesn't show it, but there is a small loop for a cord to go through so I leave my charging chord handing from there so all my cords are close together and easy to manage. You can put the headphones on the hook and swing them out of the way under your desk. I put one on the side table for my headphones.
👤I didn't expect to write a review on this. I thought I knew what I was getting. This is a cheap, easy to scratch plastic. The cable clip would be better not there. The only. The mechanism for twisting the hook into different positions is a nice thing about this. You only need to rotation from 90 degrees and 180 degrees. The hook is pretty loose and you can position it anywhere from 0 to 180. I would have given it a pass, but the junk quality means it should be a lot cheaper than other METAL items. It would be a good deal at five bucks, since I got it for twelve ninety nine. If you don't know better, maybe eight. No way in over ten. I'll probably keep it because it's not worth it with the Pandemic. It will have to do.
The wood headphone stand was finished in dark walnuts. It will work with almost all headphones. The base is 4.5" x 5.5" and has felt pads. It is designed to display your most prized headphones. It's great for your home office, studio, bedroom or both.
👤I bought these to hold my headphones. I went with this product because they match the stand nicely. There were obvious defects in the finish and grain of the stand. I had to add some stain to cover the scratches on the inside veneer. The finish was not good and it was easy to scratch the unit further. After fixing the defects, I sprayed it with several coats of polyacrylic and it looked better. It doesn't scratch anymore. There is a The bottom pads were not touching the table. They missed the mark because they were too high up. I had to peel and re- apply to get it. They look great now that they have some work done. If you don't want to spend time after a dud, beware.
👤The leather headband on my Audio-Technica stuck to the top of the stand and ripped off the underside of the band. These are a cheap imitation of the real stand, so who knows what kind of lacquer they used? If you buy this, I would recommend putting something over the wood. There is a The felt pads on the bottom of the stand don't touch the surface of the stand, because it's not flat. You might want to watch what you put on the stand.
👤There was unfinished work on one of the corners. I decided to keep it even though it's cheap and barely noticeable. There is a I wish this was a bit shorter and thinner. If you have a newer or better phone, the risk of stretching too much is there, so would prefer it to have a little play. There is a It was sturdy and came with pads so it wouldn't scratch my desk. My butcherblock desk has a walnuts finish. There is a This deserves a 4-5 stars if not for theunfinished corner out of the box.
👤The layers of plywood were separated on one side by the cracked side of the box. Even that finish had a slight and visible smudge, but it still looked and felt all right. I would have kept it and probably refinished it after a light sanding. The color shown in the photos is correct. If you can get an undamaged one, and plan as I did to improve the finish, I think this is a good value for $20, and with free Amazon returns you are not running any risk. I can't pay the full $170 for a real one from the original manufacturer, even if I wanted to, because I've seen what this is in person. I'll either buy a plastic one or go without a stand.
👤It's okay. At work, I get praise for it. There is a If you look closely, you'll see some craftsmanship issues. There isn't enough poly used in some spots. I think I could lightly sand it down and poly it myself. I don't care enough. There is a I will update if it does destroy my headphones. I have kept both of my Pros on these stands. There is a It's a tenth of the price of a real-deal. I would recommend it if you don't want to use a stand for headphones.
1 year of free USA based customer service. Questions or concerns? They are here and happy to help. The Headset Stand holder is made of sturdy and elegant material. The base is 4.3 inches wide and the headphone holder is about 10 inches high. The Wood dual headphones stand is a low center of gravity design and can hold 2 headphones at the same time, no need to worry about finding a place to put your headphones. The dual wooden desktop headset stand is compatible with most headsets and is especially suitable for large gaming headsets like Bose/Sony/Beats/ ATH/Senheiser/Gradolabs/AKG/JBL/Philips/Westone. It is possible to put the elegantWalnut Wood Headphone holder in the home, office, school, recording studio, bedroom, study or game room. This is a high-quality headphone holder. The Headphone Stand Wood package includes a wood Headset Stand, 2 screws, and a wrench. Please watch the video to learn how to use the headset stand holder better. Please contact them if you have any questions.
👤I was looking for a few rare features in a stand for headphones, and I think I have found them with this stand. I needed something that held a large headphones and would support them by the metal band, rather than the leather head strap. I was a bit worried about the stability of the stand, but I haven't noticed any issues so far.
👤It's very sleek and elegant. The headband and rod holder are of the highest quality and don't bend even the most heavy loads. The base of this stand is not quality. The entire assembly is only around 200 grams in weight, with the base around 150g. If you put your headphones towards the end of the wood, it will topple over, even with the lightest of headphones. There is a It's a shame because this stand could easily accommodate two headphones if the base was weighted, but in it's current form, even my HD650s need to be placed right over the base to balance it. If I try and put a ZMF or other 400g+ headphones in the same place as the stand, it becomes very unstable, unless I can get the table to move enough to unsettle the stand. I replaced the base with a steel plate from an old helping hands and made the stand a lot more "premium" due to the heavier feel of the stand.
👤As long as you're careful, this looks great. I took my headphones off. It fell from my side table to my couch. The part that holds the headphones fell off when it hit the floor. There's a small metal piece that fits into the wood. I was able to glue it in with gorilla glue and it seems more sturdy now. They should have spent the extra money at the factory. I'm not sure why they didn't. It works great for my Emotiva Airmotiv GR1 headphones.
👤This stand is a great value for money. There is a It's well built for the price point and it can fit two large pairs of over- ear headphones at the same time. It's got a dense, solid metal base instead of the light plastic ones found on most similarly priced headphones stands. There is a It's also easy to assemble. There are 2 Allen screws attached and a key to put it together. There is a The only issue here is that properly heavy cans can tip it over if placed alone right on the edge, but this is not an issue by using just the most basic of common sense, or by simply placing some kind of additional weight.
👤This holder works with Bose headphones. It is easy to assemble. I liked the combination of colors. It doesn't take much space and leaves your desk looking clean. I would definitely recommend it.
👤It's easy to store my Hifiman and Sony cans. The metal frame of the Sundara has more clearance than the faux leather headband and the wired connections are off the ground. It's not easy to find a stand that can handle that. Solid build. It is elegant. I was pleased with this after looking on the Internet.
Two preset heights give you maximum control over the level of your computer screen to improve posture and prevent neck and back pain. There is a notice. It is not possible to use it for painting a wall. If you paste to the wall, it will fall down. Make sure the surface is smooth, dry and oilless, and hang your headphones after 24 hours to make sure the hanger is firmly stuck. 500g is the max total weight. The headset holder with a magnet can be used when it is not in use. The arm of your headphones is covered with a soft rubber pad to protect it from slipping and scratching. The headphone hook has a strong sticky design, which can be applied to any smooth and clean surface. Hold your earphone in a firm position. Remove the sticker and stick it under your desk. It's great for hanging cables, hats and other gadgets to the kitchen counter, bookshelf, studio and company. A multi-purpose hook. The under desk mount is compatible with almost all wired and wireless headphones.
👤Does what it says it does. No issues.
👤I like the design. It's easy to hide and doesn't get in the way. It flips closed when you don't use it for headphones. It was easy to install, just remove the paper from the device and stick it on the spot you want it. The second adhesive pad they sent will help if The adhesive ever wears out. Overall, a great purchase, it does what I wanted it to do.
You can get a refund within 60 days or a free replacement within 12 months if you have non-human reasons. You can contact them via Amazon Messages if you have any questions. Simple and space-saving. Their unique and stylish headphone hanger is made from solid aluminum alloy and wood to provide a stable foundation for your headphones and clear some space on your desk. TR902 is taller than other headphone stands and has a larger cable holder to keep it balanced. STABLE & ANTI SLIP. Their headset holder has a wooden cable holder at the bottom that can hold your phone in a variety of positions without scratching or damaging it. Their headphone hanger is perfect for keeping your headphones in perfect condition, whether you use it on your desk at work or at home. The convenience and company are two things. Their headset hanger is compatible with major brands including Bose, and Audio-Technica, and is 5 cm at the headband.
👤The Bose headphones are sticking to the wood and starting to peel off, despite the stand looking great. Thanks for ruining my headphones. I am not happy with the purchase.
👤I was looking for a headset stand to hold my new purchases. The stands are expensive. I kept scrolling past the stands. I came across this. I knew it was the one because it looks stunning and the reviews are great. It's no wonder why. Assembly is a no-brainer. The base and stand are part of it. Push them together! It's done! Ready to leave! It takes 2 seconds. There is a The headband rests on the curved top part of the stand. I thought it was a square. I thought I might have to modify it. It fits my headset perfectly. The edges do not dig into it. There are pictures of this curve. There is a The base is covered with a big grip. There is a The metal is beautiful. It feels strong. Excellent quality. There is a The only complaint I have is that my bamboo pieces are different shades. I'll probably be the only one to notice. I would have liked it to be matching. 5 stars would recommend anyone.
👤The shipping box was almost weightless when I picked it up. There is a The unit works well. The base is large enough to hold it up if the cord is tangled around the shaft. The thin aluminum shaft works well for the HD800 headband, but it's a bit narrow for the Audeze LCDs, and it would work better if the dip in the middle wasn't there. I ordered the Woo Audio double stand to sit by my main system, even though I have this one in the bedroom. It's not overpriced by much. I don't think I need two stands. The banana hook is too narrow for the HD800s or the Focal Clears, so I could use one of the steel strips in the suspension headband. The banana hanger worked well for the HD600s. The all-metal banana hanger is my favorite for cost effectiveness, but the hook is too narrow for headbands of more than an inch.
👤The bamboo version is reviewed. There is a I'm happy with the $25 that I paid for these. The bamboo base and top piece are very well made. The quality of the stand is excellent. It is very strong. I have a pair of HD 800 S that are heavy, and this stand doesn't flinch. The base is large and the aluminum neck is strong. There is a This is a five star stand, and it is 888-282-0465 for my Sennheiser HD 598s. If you have lighter weight headphones, what I'm about to mention won't ever apply and this gets a huge recommendation from me. If you have heavier headphones, the top piece of them can cause problems with the soft material of the headband. The bamboo is hard and the sides are sharp, so that's why it's hard. It would have been great if there was a softer material on the top piece that would allow headphones to sit on it without putting too much pressure on the band near the sides. There is a I took this down to four stars because of the creasing on my headphones. I'd give these five stars if I hadn't bought those and used my other weighted pairs. It is an attractive stand that stays in place. I got a wooden stand that looked like an Omega symbol, and I have another one. It works well for the headband, but it's hard to get headphones off. It's not as strong at the base. I'm glad I bought this, but my 800 S headphones are on the older stand until I find a solution to the creasing or something soft for that slot.
There is an optional screw mounting hardware. An extra 3M pad is also included. The foundation for your headphones is made from solid wood. Give your headphones a stylish resting place and keep your workspace clean and organized. It fits most headphones with a headband width of 1.57 cm and device height of 9.84 cm. It's a unique decoration for home, office, studio, bedroom or next to your TV because of its environment friendly nature. The curve shape makes the stand more stable. Designed to protect your headphones.
👤I am very happy with the leather covered stand I bought. It fits all of my headphones. The stand is sturdy and looks good. The stand height and stand width are taken into account when determining the ear cup width. If you have large round ear pads, the stand width may be narrow for long term storage of your headphones. The height is fine for me.
👤I own a pair of Bose Quiet Comfort noise-cancelling headphones. There is a The Bose headphones fit right on this. There is a The Kokoon's also fit. They are larger and heavier than Bose, but they are not so large that they look ridiculous on the stand. If you don't want any kind of overlap, look elsewhere. I use the stand more for the Kokoon's because they need to replenish their batteries, so I have a place to put them. I wanted a black wooden stand, but at the moment there isn't a great selection for that on Amazon, since the width is only 3-inches. There is a The quality of the stand is very good and not likely to fall over. I wasn't concerned with the fact that most headphones won't be one-handed, especially if your headphones cling to the head.
👤It's difficult to remove your HP's with one hand from the unit without snapping your ear cups together, and the Omega style of stand will compress your ear pads premature. It doesn't add to the longevity of your headphones.
👤My wife was always leaving here with expensive headphones on, begging to be stepped on while she was working from home. I had seen stands like this before and they looked like a good solution, but they were more expensive than I was willing to pay. I decided to give it a try as a Mother's Day gift after I stumbled upon it on Amazon. The Omega Walnut color is very well built and looks really nice. My wife likes it and her headphones are now safe and out of harm's way. It is recommended for anyone looking for a safe way to store their headphones.
👤The construction is attractive. The part that supports the headphones' depth is a tad over 3 inches. These are useful for smaller headphones. The "on ear" type is the largest recommended. The types around the ear would partly hang off the wood. Other models have a depth that is at least an inch deeper.
👤The item is in black leather. One foot on the stand was a bit loose after the wrong item was received. Called, returned, and received the wrong item again. It was a gift and I'm a bit annoyed. Had the correct item been sent, I think it would have been a hit. If you can find a stand that is cheaper and better, then buy it, as I don't think it's worth what you paid. I can't recommend buying it from the seller.
👤I have different styles. I use them to hold headphones. They're lovely, the wood is sturdy, good finish, and they fit all major large full size headphones without a problem. They're so cheap these days that you can't get them for less than $20, which is fine with me. Good standing.
The rubber padded headphone is used. The rubber pads design of the headphone stand will make sure that leather headphones are protected from scratches. The base is made of natural marble and has a wide variety of colors and patterns. Each marble base has a unique style and taste. The beech wood supports the headphones. The smooth curve of the wood can protect your headphones from scratches. This well-designed headphone hanger is a great decoration for your home, office, studio, or wherever you use your computer. This wood stand is compatible with many headphones. Beoplay H9i, Astro A50, etc. The marble base can be assembled with the simple tools included in the hardware pack.
👤The marble and maple stand is very attractive. It holds the headset well and the shape is great for not changing the padding. The base is heavy and won't tip over. It was broken when it arrived. The base is heavy enough to break the connection between the post and holder. It was easier to fix it with wood glue. The packaging needs to be changed.
👤I would buy it again. It's easy to put together and it's weighted so that it doesn't tip over if you have heavy headphones.
👤The product is easy to assemble and looks great.
👤I love this. Adding a couple to the collection is something I'm thinking of doing.
👤Bekannte gekauft, fr deren, ist den Kopfhrer Shure Aonic 50. There is a Passt perfekt, die Auflage ist. Ich ist die kleinen Flche eingedrckt. Die Ohrpolster ist die Hrers knnen frei hngen. Sondern knnen. Ihren spektakulren Haltern, die den teuren Hrer ruinieren, ist wie manchen bldsinnig. Im Einrichtung passen Holz und Marmorfu. So an. Es ist schn, und hat unten in Moosgummipolster. Alles in allem are guter Preis-Gegenwert.
👤There is a Produkt. Leider is a person. berhaupt ist, passt die Marmor. I am gerne behalten.
👤Zu. It is called weihnachten. Geschenk bestellt. Ihren Fotos ist aus wie. Es ist gut. Weiter empfehlen!
Headphone hanger wood products from Apphome. In this article about headphone hanger wood you can see why people choose the product. Avantree and Onegenug are also good brands to look for when you are finding headphone hanger wood.
Apphome, Avantree and Onegenug are some of the best brands that chosen by people for headphone hanger wood. Find the detail in this article. Elevation Lab, Eurpmask Choose The Color Of Europe and Casanuva are also brands that their products are worth to check.